Viega Eco Plus WC element, individually height-adjustable
Product information
Viega Eco Plus WC element, individually height-adjustable
Viega Eco Plus
| Year built (from): | 01.07.2013 |
Trade mark rights exist for this document, further information can be found at viega.com/legal .
Target groups
The information in this instruction manual is directed at the following groups of people:
Heating and sanitary professionals and trained personnel
SHK-FachkräfteTrained electricians
ElektrofachkräfteOperators
Consumers
Drywall builder
It is not permitted for individuals without the abovementioned training or qualification to mount, install and, if required, maintain this product. This restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with the general rules of engineering and the Viega instructions for use.
Handover to the user
This document contains information about the operation and maintenance of the washbasin system. Please make sure to hand the document over to the customer / operator / user of the washbasin system after mounting.
Labelling of notes
Warning and advisory texts are set aside from the remainder of the text and are labelled with the relevant pictographs.
DANGER!
This symbol warns against possible life-threatening injury.
WARNING!
This symbol warns against possible serious injury.
CAUTION!
This symbol warns against possible injury.
NOTICE!
This symbol warns against possible damage to property.
INFO!
Notes give you additional helpful tips.
About this translated version
This instruction for use contains important information about the choice of product or system, assembly and commissioning as well as intended use and, if required, maintenance measures. The information about the products, their properties and application technology are based on the current standards in Europe (e. g. EN) and/or in Germany (e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/Germany. These should serve as recommendations in the absence of corresponding national regulations. The relevant national laws, standards, regulations, directives and other technical provisions take priority over the German/European directives specified in this manual: The information herein is not binding for other countries and regions; as said above, they should be understood as a recommendation.
Standards and regulations
The following standards and regulations apply to Germany / Europe. National regulations can be found on the relevant web site of your country at viega.com/standards .
Regulations from section: Fields of application / Mounting conditions
Scope / Notice | Regulations applicable in Germany |
|---|---|
suitable masonry walls | EN 1996‑1‑1 |
suitable concreted walls | DIN 1045 |
suitable support profiles | DIN 18183 |
Regulations from section: Sound protection
Scope / Notice | Regulations applicable in Germany |
|---|---|
Fulfilled noise protection requirements | DIN 4109 |
Fulfilled noise protection requirements | DIN 4109 (additional sheet 2) |
Fulfilled noise protection requirements | VDI 4100 SSt I-SSt II |
Product description
Overview
The WC element is equipped as follows:
- 1 - Viega Eco Plus element
- 2 - revision shaft
- 3 - Viega concealed cistern
- 4 - guide shafts
- 5 - gas pressure spring
- 6 - drain elbow
- 7 - adjustable feet
- 8 - cover plate contact surface
- 9 - threaded rods for fixing sanitary objects (gauges for bore hole 180 mm)
- 10 - hydraulic hose
- 11 - marking 1.0 m above the upper edge of the finished floor
- 12 - fixing set
Operating mode
The height-adjustable WC element is operated without electronics and functions with the help of a gas pressure spring.
The gas pressure spring enables continuous adjustment of the seat height.
Lowering WC
When the actuating button is pressed and there is a load of at least 60 kg (body weight and WC ceramic), the ceramic is lowered by a maximum of 80 mm.
Lifting WC
When the actuating button is pressed and there is no load on the WC ceramic, the WC ceramic is raised by a maximum of 80 mm by the gas pressure spring.
Compatible components
The WC element is compatible with all common WC ceramics, even with larger projection (barrier-free).
INFO!
The following lists contain a selection of the compatible and incompatible WC ceramics.
Should you have any questions on this subject, please contact the Viega Service Center.
Unrestricted compatible WC ceramics
Manufacturer |
|---|
Duravit |
Ideal Standard |
Keramag |
Villeroy & Boch |
Series | Mod.-No. / Art.-No. |
|---|---|
Architect | 254609 |
Darling New | 254409, 254509, 254909, 255709 |
D-Code | 22109, 221109, 253509 |
DuraStyle | 253609, 253639, 253709, 253809, 253909, 254009, 254209, 255109, 255209, 255909 |
DuraPlus | 19209, 20609, 254709 |
Happy D.2 | 222109, 222209, 255009 |
Series 1930 | 18209 |
Starck 1 | 21009 |
Starck 2 | 253309, 253409, 253439 |
Vero | 221709, 221739 |
Calla | K 3053 01 |
Connect | E 8017 01, E 8018 01, E 8232 01 |
Dea | T 3290 01 |
Soft Mood | T 3226 01 |
Strada | J 4521 01 |
Tonic | K 3157 01 |
Ventuno | T 3164 01 |
Washpoint | R 3427 01 |
Icon | 204000, 204060 |
Xeno | 206250 |
it! | 201900, 201950 |
Flow | 207900 |
Flow 300 | 207950 |
Renova Nr1 | 203040, 203140, 203045 |
Renova Nr1 Plan | 202150, 202160, 202170 |
4U | 203430, 203450, 203460 |
Dejuna | 208530 |
Subway | 6600 10 XX |
Amadea | 7C96 B0 XX |
Architectura | 5685 10 XX |
O.novo | 5660 10 XX |
Omnia | 5684 10 XX |
Omnia pro | 7615 10 XX |
Pure stone | 5670 10 XX |
Incompatible WC ceramics
Manufacturer |
|---|
Duravit |
Ideal Standard |
Villeroy & Boch |
Series | Mod.-No. / Art.-No. |
|---|---|
2nd Floor | 222009 |
Esplanada | 255309, 255409 |
Pura Vida | 221909 |
Starck 3 | 220009, 220109, 220209, 220309, 220609, 221509, 222509, 222609, 222709 |
Eurovit | V 3906 01, V 3403 01 |
San ReMo | R 3401 01, R 3493 01, R 3404 01 |
Connect_Freedom | E 6076 01, E 607501 |
Moments | K 3113 01 |
Lifetime | 5672 10 XX |
My Nature | 5610 10 XX |
Subway 2.0 | 5614 R0 XX |
Aveo | 6612 10 XX |
Hommage | 6661 B0 XX |
Joyce | 5670 R0 XX |
La Belle | 5627 10 XX |
Memento | 5628 10 XX |
Sentique | 5622 10 XX |
Compatible flush plates
Product |
|---|
Standard |
Visign for Style |
Visign for More |
Visign for Care sensitive |
Visign for More sensitive |
Visign for Public |
Name | Model |
|---|---|
Flush plate Standard 1 | 8180.1 |
Flush plate Visign for Style 10 | 8315.1 |
Flush plate Visign for Style 11 | 8331.1 |
Flush plate Visign for Style 12 | 8332.1 |
Flush plate Visign for Style 12 | 8332.4 |
Flush plate Visign for Style 13 | 8333.1 |
Flush plate Visign for Style 14 | 8334.1 |
Functional unit | 8332.3 |
Flush plate Visign for More 100 | 8352.1 |
Flush plate Visign for More 101 | 8351.1 |
Flush plate Visign for More 102 | 8353.1 |
Flush plate Visign for More 103 | 8355.1 |
Flush plate Visign for More 104 | 8354.1 |
Flush plate sensitive Visign for Care | 8352.21 |
Flush plate sensitive Visign for More 100 | 230 V 8352.11 |
Flush plate sensitive Visign for More 100 | 6.5 V 8352.12 |
Flush plate sensitive Visign for More 103 | 230 V 8355.11 |
Flush plate sensitive Visign for More 103 | 6.5 V 8355.12 |
Flush plate Visign for Public 1 | 8326.1 |
Flush plate Visign for Public 2 | 8327.1 |
Flush plate Visign for Public 5 | 8326.16 |
Flush plate Visign for Public 6 | 8326.15 |
Remote actuation Visign for Public 1 | 8326.21 |
Cover plate Visign for Public | 8326.9 |
Sound protection
The WC element complies with the noise insulation requirements specified in section Regulations from section: Sound protection .
Technical data
Product data
adjustable seat height |
|---|
Wall construction |
Drive weight |
Drive weight |
Release force for the actuating button |
Load on middle of ceramic |
approx. 400–480 mm1) |
max. 45 mm |
min. approx. 60 kg |
max. approx. 28 kg |
approx. 30 N |
max. 400 kg |
| 1) | at factory intended fixing height of 310–390 mm |
Flush volume
Small flush volume |
|---|
Large flush volume |
Factory setting | approx. 3 l |
Setting range | approx. 3–4 l |
Factory setting | approx. ca. 6 l |
Setting range | approx. 6–9 l |
Accessories
Required accessories
A cover plate (model 8356.8) made of TG clear / light grey.
Optional accessories
The WC element can be extended by connecting an installation set (model 8350.14) and an installation frame (model 8350.23 or model 8330.21) for a tile-level flush plate.
The installation set is suitable for the connection of an electrical actuation. The installation set consists of an empty pipe and a hollow wall socket. The empty pipe connects the hollow wall socket with the concealed cistern.
If a WC ceramic that weighs more than 28 kg is mounted, a gas pressure spring, model 8174 is also required. This gas pressure spring replaces the gas pressure spring supplied.
Handling
Assembly information
Mounting conditions
Suitable walls
The Viega WC element is suitable for mounting on masonry wall constructions and support profiles pursuant to the regulations in section Regulations from section: Fields of application / Mounting conditions .
The WC element may only be mounted on even wall surfaces.
Construction height
With the construction height, the marked height of the upper edge of the finished floor must be observed.
INFO!
Errors caused by incorrect construction heights may limit the setting range after the completion of the work. A correction and therefore a limitation of the setting range is only possible up to max. 20 mm. The setting range is reduced accordingly from 80 mm to 60 mm.
Installation depth
The installation depth is 200 mm.
WC ceramic
The WC element can only be used in combination with wall-hung WCs (fixing gauges for bore hole 180 mm).
On request, wall-hung WCs with a fixing gauge for bore holes of 230 mm may be used.
Actuation
The WC element can be extended by a remote actuation Visign for Public1 (model 8326.21) or by an electronic actuation (model 8350.31 or 8350.32). The corresponding actuation method must be prepared before the WC element is clad and tiled.
The corresponding empty pipe (included in the scope of delivery of the remote actuation) is required when preparing the remote actuation Visign for Public1.
Installation dimensions
Dimensions
Required tools
The following tools are required for mounting the WC element:
drill with 10 mm drill bit
ratchet with sockets: 13 mm / 17 mm
fork or ring spanner: 10 mm / 13 mm / 17 mm / 19 mm
fork or ring spanner: 27 mm
Allen key: 5 mm
Assembly
Mounting WC element
INFO!
Masonry and concreted walls
You should use a support bracket (model 8165) when mounting multiple WC elements with an interval of > 490 mm. Observe the instructions for use of the support bracket when mounting.
Masonry wall
-
Determine and mark fixing points.
X1: 390 mm (model 8180.73)
X2: 440 mm (model 8173)
X3: 1110 mm.
-
Drill holes.
-
Mount the fixing set with the fork spanner (size 17).
-
Align WC element.
-
Set the installation depth of the pre-wall element (180–250 mm) with the fork spanner (size 17).
-
Determine construction height in accordance with the on-site marking of the upper edge of the finished floor.
INFO!The construction height must be determined and adhered to exactly.
There are only limited possibilities available to remedy errors made during this assembly step. Construction height
-
Attach WC element to the wall.
-
Attach WC element to the floor using the fork spanner (size 13) and the screws and dowels supplied.
On-site support profile
-
Determine the fixing points.
-
Align element.
-
If necessary, adjust (pre-mounted) foot depth from 75 mm to 50 mm.
-
Pull the foot out and turn by 90°.
-
Attach WC element to the floor using the fork spanner (size 13) and the screws and dowels supplied.
-
Determine construction height in accordance with the on-site marking of the upper edge of the finished floor.
INFO!The construction height must be determined and adhered to exactly.
There are only limited possibilities available to remedy errors made during this assembly step. Construction height -
Pull WC element up (cutting check) and align.
-
Tighten feet with the fork spanner (size 17).
-
Screw the WC element together laterally with the support profiles (size 17).
Connecting concealed cistern
Laterally extricable water connection
If there is not enough space when pressing the water connection, the water connection can be pulled out to the side.
-
Screw the ½ inch connector into the wall lead-in.
Counter with a fork spanner (SW 27).
-
Loosen plastic union nut.
-
Pull out wall lead-in.
-
Press connection.
-
Push wall lead-in back into the plastic clamp.
The position of the key surface (SW 25) must be up or down.
The clicking into the groove signals the correct position.
-
Re-tighten the union nut.
-
Loosen (SW 19) flexible hose onto the filling valve.
-
Open corner valve.
-
Flush pipeline.
-
Close corner valve.
-
Re-mount (SW 19) the flexible hose onto the filling valve.
Conversion water connection upwards (optional)
-
Loosen (SW 19) flexible hose onto the corner valve.
-
Unscrew plastic union nut.
-
Pull the corner valve inwards out of the wall lead-in.
-
Remove plastic union nut.
-
Remove the wall lead-in inwards.
-
Loosen the closing cap on the left-hand upper side of the concealed cistern.
-
Close opening on the side with the closing cap.
-
Push wall lead-in from inside into the upper opening.
-
Insert the corner valve back into the wall lead-in.
-
Screw plastic union nut back onto wall lead-in.
-
Re-mount (SW 19) the flexible hose onto the corner valve.
Mounting the drain elbow
Observe the following when mounting:
professional mounting
prevent sagging
prevent tensile strain
-
Remove template (polystyrene).
-
Attach drain elbow laterally onto the element using the fixing elbow supplied.
Mounting possible on both right and left.
Alternatively: Secure the drain elbow onto the wall or floor without the fixing material supplied, taking into account the fixing sizes.
INFO!
Installing pipelines vertically through the bare concrete floor is only possible with the drain elbow (model 8095, Art. No. 713 744).
The screed height must be at least 85 mm.
Preparing optional actuation versions
Prepare remote actuation
The corresponding empty pipe (included in the scope of delivery of the remote actuation) is required when preparing the remote actuation Visign for Public1 (model 8326.21).
-
Lead the empty pipe from the hollow wall socket into the concealed cistern.
Distance from the remote actuation to the cistern (x)
min. 1.0 m
max. 1.7 m
Prepare electrical actuation
A corresponding empty pipe (not included in the scope of delivery of the electrical actuation) is required for the preparation of the electrical actuation (model 8350.31 or model 8350.32).
-
Lead empty pipe from the switch or button into the concealed cistern, to connect the concealed socket and concealed cistern.
Positioning of the cistern power pack
X1= max. 0.75 m
X2= max. 2.75 m with an extension cable, 1 x article number 628 505
X3= max. 4.75 m with two extension cables, 2 x article number 628 505
Set up element for wall covering – using the template
-
Unscrew the threaded rod of the WC fastening so that it projects out by approx. 45 mm.
-
Attach the template (polystyrene) to the element.
Make water connection to the concealed cistern.
-
Double clad the pre-wall element (2 x 12.5 mm).
-
Clad up to the template.
-
Plaster board must not be attached to the height-adjustable internal frame.
-
Lay tiles up to the template.
Replace gas pressure spring
INFO!
For the mounting of a WC ceramic that weighs more than 28 kg, a gas pressure spring, (model 8174) is also required. This gas pressure spring replaces the gas pressure spring supplied.
Requirements:
WC ceramic is at the lowest position
Following components are removed:
WC ceramic
Cover plate
Actuating button / Hydraulic actuation
Cover frame
-
Remove gas pressure spring by lowering the top and bottom 5 mm Allen screw.
-
Insert new gas pressure spring and attach with Allen screws.
Re-mount following components:
Cover frame
Actuating button / Hydraulic actuation
Cover plate
WC ceramic
Mounting the cover plate
-
Mount the bearing surface (H support) for the cover plate flush with the finished wall surface (size 17 / 19).
-
Loosen the four threaded nuts on the element (size 17).
-
Loosen the four front threaded nuts on the sides of the H support (size 17).
-
Screw out or screw in the threaded nuts to align all four points of the H support flush with the finished wall surface.
-
Check it is flush with the wall surface using a spirit level.
-
Tighten the rear threaded nuts at all four points of the H support (size 17).
When doing so, hold the threaded rods with a flat-blade screwdriver.
-
Tighten front threaded nuts (size 17).
-
Check to ensure they are flush.
-
Unscrew the threaded rods for the fixing of the sanitary object to the required size.
When doing so, counter with threaded nuts (size 19).
-
Fit the supplied seal in the cover frame on the front.
-
Apply the silicone seal to the rear of the cover frame.
-
Lead hydraulic actuation unit through the cover frame towards the front.
-
The radius of the hydraulic actuation must be at least 50 mm.
This prevents the hydraulic actuation from buckling.
-
Align cover frame.
Attach cover frame to the element with the recessed head screws supplied.
-
Remove transport lock (size 10).
Height-adjustment of the WC is only possible, if the transport lock is removed.
-
Mount cover plate.
-
There must be an interval of at least 5 mm the upper edge of the finished floor and the lower edge of the cover plate.
Mounting actuating button
-
Remove cover plate.
Protect with packaging corners.
-
Screw the sleeve onto the hydraulic cylinder as far as it will go.
-
Insert the hydraulic cylinder from the rear through the opening in the cover plate.
-
Screw the rosette through the cover plate from the front onto the hydraulic cylinder.
-
Counter screw the sleeve from the rear side.
-
Align the rosette with the help of the arrow symbols.
-
Screw the actuating button hand-tight onto the hydraulic cylinder from the front.
Do not use glue or the like to secure the button.
-
The actuating button has been mounted.
-
Place the cover plate on the element.
-
Check clearance between wall and cover plate (min. 5 mm).
Limiting the setting range
The length of the gas pressure spring, and therefore also the setting range of the WC, can be limited by max. 20 mm if the upper edge of the finished floor is higher than intended.
The cover plate can be prevented from touching by using spacer washers (4 mm each).
A maximum of five spacer washers may be used.
Requirements:
WC ceramic is at the lowest position
Following components are removed:
WC ceramic
Cover plate
Actuating button / hydraulic actuation
Cover frame
-
Remove gas pressure spring by lowering the top and bottom 5 mm Allen screw.
-
Place the relevant number of spacer washers below the piston rod of the gas pressure spring.
Attaching protective sticker
Depending on the version of the WC lid, it may be that there is contact with the wall during the height adjustment of the WC. Attaching the protective sticker prevents damage to the surface in the possible contact area on the wall and on the WC lid.
-
Determine possible area of contact between the wall and the WC lid on the wall.
-
Clean possible contact area on the wall.
-
Remove the protective foil from the protective sticker and attach in the possible contact area.
INFO!
The protective sticker should remain on the wall to protect the wall and the WC lid from damage to the surface in the case of further height adjustments.
Preparing mounting for required accessories
Mounting the connection set for WC ceramic
-
Adapt the length of the flushing pipe and drainpipe.
-
Cut the sound insulation panel to size.
-
Install the WC ceramic and sound insulation panel.
-
Align and secure the WC ceramic.
-
Seal the gap between WC ceramic and cover plate with silicone.
Use
CAUTION!
Risk of crushing
The cover plate shifts in parallel with the wall surface during the height adjustment. Due to this, there is the risk of crushing in the areas above and below the cover plate.
Keep hands and feet away from the dangerous areas.
Lowering WC
Requirements:
Total weight of min. 60 kg (body weight and WC ceramic)
WC ceramic's own weight max. 28 kg
open WC lid
-
Sit on the toilet seat.
-
Press the actuating button and continue to hold until the desired height is reached.
Lifting WC
Requirements:
unladen toilet seat
WC ceramic's own weight max. 28 kg
-
Press the actuating button and continue to hold until the desired height is reached.
Cleaning and maintenance
Maintenance and cleaning work may only be carried out by specialist trade professionals or qualified experts.
Cleaning
The cover plate may only be cleaned using mild cleaning agents containing soap.
Scouring milk and cleaning agents or disinfectants containing the following ingredients may not be used:
alcohol
ammoniac
hydrochloric acid
phosphoric acid
acetic acid
NOTICE!
Pipe damage
Do not use a cleaning spiral around the area of the flexible drain elbow on the WC connection.
Maintenance
The mechanism of the WC element is maintenance-free.
Cleaning and maintenance of the concealed cistern
In consideration of the mechanical, chemical and physical conditions, the concealed cistern is constantly laden.
For this reason, the components must be cleaned, as required, and the drain and filling valve seals renewed.
In areas or regions with hard water due to calcium or magnesium salts, there is the risk of limescale deposits developing on the inlet and drain valves.
The valves may have to be replaced, depending on the extent of deposits.
Disposal
Separate the product and packaging materials (e. g. paper, metal, plastic or non-ferrous metals) and dispose of in accordance with valid national legal requirements.